Hyundai HI RUN n 700 Скачать руководство пользователя страница 23

Страница: 23 / 186

N700 Operating Instructions and Parts Manual

1. General Description

1.1.2 Instruction

manual

This instruction manual is the manual for the N700 inverters.

Before operation of the inverter, read the manual carefully. After reading this manual, keep it on

hand for future reference.

1.2

Questions and Warranty of the Unit

1.2.1

Questions on Unit

If you have any questions regarding damage to the unit, unknown parts or for general inquiries,

please contact your LOCAL HYUNDAI BRANCH with the following information.

(1) Inverter

Model

(2) Production Number (Serial No.)

(3) Date of purchase

(4) Reason for Calling

①

Damaged part and its condition etc.

②

Unknown parts and their contents etc.

1.2.2

Warranty for the unit

(1) The warranty period of the unit is one year after the purchase date. However the warranty will

be void if the fault is due to;

①

Incorrect use as directed in this manual, or attempted repair by unauthorized personnel.

②

Any damage sustained other than from transportation (Which should be reported

immediately).

③

Using the unit beyond the limits of the specifications.

④

Natural Disasters : Earthquakes, Lightning, etc

(2) The warranty is for the inverter only, any damage caused to other equipment by malfunction

of the inverter is not covered by the warranty.

(3) Any examination or repair after the warranty period (one-year) is not covered. And within the

warranty period any repair and examination which results in information showing the fault was

caused by any of the items mentioned above, the repair and examination costs are not

covered. If you have any questions regarding the warranty, please contact either your Local

HYUNDAI Branch.

Содержание HI RUN n 700



























































































































































































Результаты поиска

Содержание HI RUN n 700

Отзывы:

Похожие инструкции для HI RUN n 700

Бренды по названию

Популярные бренды

Hyundai HI RUN n 700, Инструкция по эксплуатации

Результаты поиска

Содержание HI RUN n 700

Отзывы:

Похожие инструкции для HI RUN n 700

Бренды по названию

Популярные бренды