Hyundai HI RUN n 700 Скачать руководство пользователя страница 16

Страница: 16 / 186

N700 Operating Instructions and Parts Manual

CONTENTS

General Description ................................................................................................................................. 1

1.1

Inspection upon Unpacking............................................................................................................ 1

1.1.1

Inspection of the unit ......................................................................................................... 1

1.1.2

Instruction manual............................................................................................................. 2

1.2

Questions and Warranty of the Unit ............................................................................................... 2

1.2.1

Questions on Unit.............................................................................................................. 2

1.2.2

Warranty for the unit.......................................................................................................... 2

1.3

Appearance.................................................................................................................................... 3

Installation and Wiring.............................................................................................................................. 4

2.1

Installation ...................................................................................................................................... 4

2.1.1

Installation ......................................................................................................................... 5

2.1.2

Blind cover of wiring parts ................................................................................................. 7

2.2

Wiring ............................................................................................................................................. 8

2.2.1

Terminal Connection Diagram (sink type) ......................................................................... 9

2.2.2

Main circuit wiring............................................................................................................ 12

2.2.3

Terminal connection diagram .......................................................................................... 17

2.2.4

Digital operator wiring ..................................................................................................... 19

Operation ............................................................................................................................................... 20

3.1

Operating ..................................................................................................................................... 21

3.1.1

Operation setting and a frequency setting by the terminal control. ................................ 21

3.1.2

Operation setting and frequency setting with the digital operator. .................................. 21

3.1.3

Operation setting and frequency setting from both the digital operator and the terminal

operator........................................................................................................................... 21

3.2

Test Run ....................................................................................................................................... 22

3.2.1

To input the operation setting and the frequency setting from the terminal control. ....... 22

3.2.2

Operation setting and the frequency setting from the digital operator............................ 23

Parameter Code List .............................................................................................................................. 25

4.1

About Digital Operator.................................................................................................................. 25

4.1.1

Name and contents of each part of Standard-type digital operator (OPE-N7) ............... 25

4.2

Code List ...................................................................................................................................... 28

4.2.1

Monitor mode(d-group) ................................................................................................... 28

4.2.2

Trip & Warning monitor mode(d-group) .......................................................................... 28

4.2.3

Fundamental functions(F-group)..................................................................................... 29

4.2.4

User setting functions(U-group) ...................................................................................... 30

4.2.5

Operating curve setting(A-group).................................................................................... 30

Содержание HI RUN n 700



























































































































































































Результаты поиска

Содержание HI RUN n 700

Отзывы:

Похожие инструкции для HI RUN n 700

Бренды по названию

Популярные бренды

Hyundai HI RUN n 700, Инструкция по эксплуатации

Результаты поиска

Содержание HI RUN n 700

Отзывы:

Похожие инструкции для HI RUN n 700

Бренды по названию

Популярные бренды