Hyundai HI RUN n 700 Скачать руководство пользователя страница 112

Страница: 112 / 186

N700 Operating Instructions and Parts Manual

9. Explanation of I-Group Function

(4) Jogging operation selection

Note)

When using the jogging function, turn FW terminal or RV terminal ON after the JG

terminal is turned ON. (It is the same when the operation command point is from the

operator.)

Fig. 9- 12 Jogging operation selection (When setting of A039 is 03, 04 or 05 and FW

terminal is turned ON beforehand, the inverter operates jogging.)

Note)

In the case that the setting of A074 is 02, data setting of DB is necessary.

(5) Set an intelligent input terminal(I001~I008) to 06 (JG). (Initial value : I003 =6)

Fig. 9- 13 Jogging operation selection in the intelligent input terminal

9.2.4

Direct current braking (DB : External DC Braking)

(1) Please set 7 (DB) to an Intelligent input terminal.

(2) DC braking is then switched by ON/OFF of DB terminal irrespective of DC braking selection

A081.

(3) Set DC braking force with A084.

(4) If DC braking time A083 is set, the Inverter output is cut off for this time period, the motor will

be free-running. After the setting time passes, DC braking is started.

(5) Please set DC braking time A085 or DC braking time by DB terminal paying attention to the

heat of the motor.

Note) Please refer to 7.10 (DC braking setting) for details.

9.2.5

Second control function (SET2)

(1) Please set 8 (SET 2) to Intelligent input terminals 1~8 (function code I001~I008).

(2) By assigning 08 (SET 2) to an intelligent input terminal and turning SET2 terminal ON/OFF

you can switch between two different inverter set-ups.

The functions which can change with SET terminal are as following.

Содержание HI RUN n 700



























































































































































































Результаты поиска

Содержание HI RUN n 700

Отзывы:

Hyundai HI RUN n 700, Инструкция по эксплуатации, Страница: 112 / 186

Результаты поиска

Содержание HI RUN n 700

Отзывы: