Husqvarna FE 350 2014 Скачать руководство пользователя страница 91

Страница: 91 / 279

14.5.3

14.5.4

WHEELS

- Lift the front wheel into the fork, position it, and insert the wheel spindle.

✓ The brake linings are positioned.

- Mount and tighten screw

Guideline

Screw, front wheel spindle

M24x1.5

45 Nm (33.2 lbf ft)

- Activate the hand brake lever multiple times until the brake linings are in contact

with the brake disc.

- Remove the motorcycle from the lift stand. (,r- p. 11)

- Pull the front wheel brake and push down hard on the fork several times to align

the fork legs.

- Tighten screws (D.

Guideline

Screw, fork stub

I1s Nm (11.1 lbf ft)

Removing the front brake disc

Preparatory work

- Raise the motorcycle with a lift stand. (,r- p. 11)

- Remove the front wheel. (,r- p. 88)

Main work

- Remove screws

Take off the brake disc.

Installing the front brake disc

Main work

- Clean the contact surface of the brake disc.

- Position the brake disc with the label facing outward. Mount and tighten

screws

Guideline

Screw, front brake disc

Finishing work

- Install the front wheel. (,r- p. 88)

14 Nm

(10.3 lbf ft)

Loctite

243

™

14.5.5

Changing the front wheel bearing

Preparatory work

- Raise the motorcycle with a lift stand. (,r- p. 11)

- Remove the front wheel. (,r- p. 88)

Main work

- Remove shaft seal rings

and

Содержание FE 350 2014
























































































































































































































































































Результаты поиска

Содержание FE 350 2014

Отзывы:

Husqvarna FE 350 2014, Руководство по ремонту, Страница: 91 / 279

Результаты поиска

Содержание FE 350 2014

Отзывы: