Husqvarna FE 350 2014 Скачать руководство пользователя страница 148

Страница: 148 / 279

18 ENGINE

18.4.4

Checking the oil pressure regulator valve

o-8

305033-10

Remove screw plug

with sealing washer @.

Remove pressure spring fs) and ball

Measure the spring length of the oil pressure regulator valve.

Oil pressure regulator valve

Minimum length of pressure spring 23.5 mm (0.925 in)

If the measured value does not meet specifications:

Change the spring.

Check ball

and the sealing seat.

If there is damage or wear:

Change the ball and machine the sealing seat.

Install ball

and pressure spring fs).

Mount and tighten screw plug

with sealing washer @.

Guideline

Plug, oil pressure regulator valve

M12x1.5

18.4.5

Checking the lubrication system

•

✓

305003-10

Check the internal rotor and external rotor of oil pumps

for damage and wear.

If there is damage or wear:

Change the oil pumps.

Check oil pump shaft @ for damage and wear.

If there is damage or wear:

146

20 Nm (14.8 lbf ft)

Содержание FE 350 2014
























































































































































































































































































Результаты поиска

Содержание FE 350 2014

Отзывы:

Husqvarna FE 350 2014, Руководство по ремонту, Страница: 148 / 279

Результаты поиска

Содержание FE 350 2014

Отзывы: