manualshive.com logo in svg

Husqvarna FE 350 2014, Руководство по ремонту, Страница: 105 / 279

Поделиться
Скачать
Husqvarna FE 350 2014 Скачать руководство пользователя страница 105

15 

15.6 

15.7 

WIRING  HARNESS,  BATTERY 

Checkin  the charging volta  e 

Condition 

The battery must be fully functional and completely charged. 

- Carry out the start procedure. (.- p. 11)

Measure the voltage between the specified points. 

Measuring point 

Plus 

(+) - Measuring point 

Ground 

(-) 

I 

Charging voltage 

5,000 rpm 

113.5 ...  15.0 V

If 

the displayed value is less than the specified value: 

103 

Check the plug-in connections from the alternator to the voltage regulator. 

Checking the  uiescent current 

- Check the plug-in connectors from the voltage regulator to the wiring har-

ness.

- Check the stator winding of the alternator. (.- p. 196)

If 

the displayed value is greater than the specified value:

- Change the voltage regulator.

Preparatory work 

- Switch off all power consumers and switch off the engine.

- Remove the seat. (.- p. 76)

Main work 

- Disconnect the negative cable from the battery.

- Measure the current between battery ground (-) and the negative cable.

•

Info

I 

The value of the quiescent current applies only to vehicles in the original 

state, i.e. without additional power consumers. 

I 

Maximum closed-circuit current

I< 

1.0 mA

If 

the measured value is higher than the specified value: 

- Disconnect the voltage regulator from the wiring harness and perform the

measurement again.

Содержание FE 350 2014
























































































































































































































































































Отзывы:

Нет отзывов