Husqvarna FE 350 2014 Скачать руководство пользователя страница 104

Страница: 104 / 279

WIRING HARNESS, BATTERY

Removin the batte

Warning

Risk of injury

Battery acid and battery gases cause serious chemical burns.

Keep batteries out of the reach of children.

Wear suitable protective clothing and goggles.

- Avoid contact with battery acid and battery gases.
-

Keep sparks and open flames away from the battery. Only charge in well-ventilated rooms.

In the event of skin contact, rinse with large amounts of water. If battery acid gets in the eyes, rinse with water for at

least 15 minutes and contact a physician.

Preparatory work

Switch off all power consumers and switch off the engine.

Remove the seat. (

p. 76)

Main work

102

Pull back the negative terminal cover

and disconnect the negative cable from

the battery.

Pull back the positive terminal cover

and disconnect the positive cable from

the battery.

Detach rubber band

at the bottom.

Lift the battery up and out.

Main work

Insert battery into the battery compartment with the terminals facing to the front.

Battery (YTX5L-BS) (

p. 204)

Reconnect rubber band

•

Info

Contact disk

must be mounted between screw

and cable

socket

with the claws facing down.

Position the positive cable and mount and tighten the screw.
Guideline

Screw, battery terminal

Slide positive terminal cover

over the positive terminal.

Position the negative cable and mount and tighten the screw.

Guideline

Screw, battery terminal

Slide negative terminal cover

over the negative terminal.

Finishing work

Mount the seat. (

p. 76)

2.5 Nm

(1.84 lbf ft)

2.5 Nm

(1.84 lbf ft)

Содержание FE 350 2014
























































































































































































































































































Результаты поиска

Содержание FE 350 2014

Отзывы:

Husqvarna FE 350 2014, Руководство по ремонту, Страница: 104 / 279

Результаты поиска

Содержание FE 350 2014

Отзывы: