Husqvarna FE 350 2014 Скачать руководство пользователя страница 16

Страница: 16 / 279

6.4

FORK, TRIPLE CLAMP

402556-10

Main work

Release bleeder screws

✓ Any excess pressure escapes from the interior of the fork.

Tighten the bleeder screws.

Finishing work

Remove the motorcycle from the lift stand.(

p. 11)

Cleaning the dust boots of the fork legs

Preparatory work

Raise the motorcycle with a lift stand.(

p. 11)

Loosen the fork protector. (

p. 14)

Main work

Push dust boots

of both fork legs downward.

•

Info

The dust boots remove dust and coarse dirt particles from the inside fork

tubes. Over time, dirt can penetrate behind the dust boots. If this dirt is not

removed, the oil seals behind can start to leak.

Warning

Danger of accidents

Reduced braking efficiency due to oil or grease on

the brake discs.
- Always keep the brake discs free of oil and grease, and clean them

with brake cleaner when necessary.

Clean and oil the dust boots and inner fork tubes of both fork legs.

Universal oil spray (

p. 258)

Press the dust boots back into their normal position.

Remove excess oil.

Finishing work

Position the fork protector. (

p. 15)

Remove the motorcycle from the lift stand.(

p. 11)

Remove screws

and remove the clamp.

Remove screws

on the left fork leg. Push the fork protector downwards.

Remove the screws on the right fork leg. Push the fork protector downwards.

Содержание FE 350 2014
























































































































































































































































































Результаты поиска

Содержание FE 350 2014

Отзывы:

Husqvarna FE 350 2014, Руководство по ремонту, Страница: 16 / 279

Результаты поиска

Содержание FE 350 2014

Отзывы: