Husqvarna FE 350 2014 Скачать руководство пользователя страница 157

Страница: 157 / 279

18 ENGINE

18.4.22 Checking the valves

200193-10

302809-10

18.4.23 Checking the valve springs

305015-10

Check the valve plate for run-out.

Valve - run-out

At the valve plate

s; 0.05 mm (s; 0.002 in)

If the measured value does not meet specifications:

Change the valve.

Check sealing seat

on the valve.

Valve - sealing seat width

Intake

Valve - sealing seat width

Exhaust

1 .40 mm (0.0551 in)

1.40 mm (0.0551 in)

155

If the sealing seat is not centered on the valve seat or deviates from the speci

fication:

Rework the valve seat.

Check the valve springs for breakage and wear (visual check).

If the valve spring is broken or worn:

Change the valve spring.

Measure the length of the valve springs.

Valve spring

Minimum length

42.00 mm (1.6535 in)

If the measured value does not meet specifications:

Change the valve springs.

18.4.24 Checking the valve spring seat

305014-10

18.4.25 Checking the cam levers

302718-10

Check the valve spring seat for breakage and wear (visual check).

If the valve spring seat is broken or worn:

Change the valve spring seat.

Measure the thickness of the valve spring seat.

Valve spring seat - thickness

0.90 ... 1.10 mm (0.0354 ... 0.0433 in)

If the measured value does not meet specifications:

Change the valve spring seat.

Check the cam levers and cam lever shafts for damage and wear.

If there is damage or wear:

Change the cam levers and/or cam lever shafts.

Содержание FE 350 2014
























































































































































































































































































Результаты поиска

Содержание FE 350 2014

Отзывы:

Husqvarna FE 350 2014, Руководство по ремонту, Страница: 157 / 279

Результаты поиска

Содержание FE 350 2014

Отзывы: