Husqvarna FE 350 2014 Скачать руководство пользователя страница 171

Страница: 171 / 279

18 ENGINE

18.5.3

Installing the shift forks

•-

18.5.4

Installing the shift drum

18.5.5

Installing the shift rails

169

Shift fork

has a smaller inside diameter; mount this in the shift groove of the

main shaft.

Mount shift fork @ in the lower shift groove of the countershaft.

Mount shift fork (D in the upper shift groove of the countershaft.

Slide on shift rollers

Tip

Fix the shift rollers in the shift forks with grease.

Push shift drum

into the bearing seat.

Put shift forks @ in the shift drum.

Info

Do not misplace the shift rollers.

Install shift rail

together with upper spring @ and the lower spring.

Install shift rail (D together with upper spring

Содержание FE 350 2014
























































































































































































































































































Результаты поиска

Содержание FE 350 2014

Отзывы:

Husqvarna FE 350 2014, Руководство по ремонту, Страница: 171 / 279

Результаты поиска

Содержание FE 350 2014

Отзывы: