Husqvarna FE 350 2014 Скачать руководство пользователя страница 149

Страница: 149 / 279

18 ENGINE

- Change the oil pump shaft.

- Check the oil pump cover for damage and wear.

If there is damage or wear:

- Change the oil pump cover.

18.4.6

18.4.7

Removing the crankshaft bearing inner race

- Fix the crankshaft in the vise.

•

Info

Use soft jaws.

- Warm up special tool

Guideline

1150 °C (302 °F)

Tool for inner bearing race (58429037037) (

p. 260)

- Push the warmed up special tool

onto the crankshaft bearing inner race,

press firmly together and pull jointly from the crankshaft.

- Take off the compensating disk.

- Repeat the operation on the opposite side.

Installing the crankshaft bearing inner race

- Fix the crankshaft in the vise.

•

Info

Use soft jaws.

- Slide on the compensating disk.

- Heat the crankshaft bearing inner race in special tool

and mount together.

Guideline

1120 °C (248 °F)

Tool for inner bearing race (58429037037) (

p. 260)

- Repeat the operation on the opposite side.

- Ensure that the new crankshaft bearing inner race is flush.

•

Info

147

After replacing the crankshaft bearings, the crankshaft end play must be

measured.

18.4.8

Changing the connecting rod, conrod bearing and crank pin

Main work

- Position crankshaft

in the press using special tool

Extrude plate, base (77229009000) (

p. 263)

- Press the crank pin with the special tool out of the upper crank web.

Pressing tool for crankshaft, complete (75029047000) (

p. 262)

•

Info

Hold the lower crank web.

- Remove the connecting rod and bearing.

Содержание FE 350 2014
























































































































































































































































































Результаты поиска

Содержание FE 350 2014

Отзывы:

Husqvarna FE 350 2014, Руководство по ремонту, Страница: 149 / 279

Результаты поиска

Содержание FE 350 2014

Отзывы: