Husqvarna FE 350 2014 Скачать руководство пользователя страница 48

Страница: 48 / 279

SHOCK ABSORBER, SWINGARM

Main work

Carefully take the shock absorber out of the vehicle toward the top.

Main work

Carefully position the shock absorber into the vehicle from above.

Finishing work

Install the manifold. (,r- p. 69)

Mount the seat. (,r- p. 76)

Install the main silencer. (,r- p. 71)

Install the right side cover. (- p. 76)

Remove the motorcycle from the lift stand. (- p. 11)

9.11

Checkin the shock absorber linka e

Preparatory work

Raise the motorcycle with a lift stand. (,r- p. 11)

Main work

Remove screw

Remove fitting

Info

Raise the wheel slightly to be able to remove the screws more easily.

Remove fitting

Take off the angle lever.

Содержание FE 350 2014
























































































































































































































































































Результаты поиска

Содержание FE 350 2014

Отзывы:

Husqvarna FE 350 2014, Руководство по ремонту, Страница: 48 / 279

Результаты поиска

Содержание FE 350 2014

Отзывы: