Husqvarna FE 350 2014 Скачать руководство пользователя страница 89

Страница: 89 / 279

WHEELS

Checkin the brake discs

Warning

Danger of accidents

Reduced braking efficiency due to worn brake disc(s).

Change the worn brake disc(s) without delay.

Check the thickness of the front and rear brake discs at several places on the

disk to see if it conforms to measurement t).

•

Info

Wear reduces the thickness of the brake disc around the area used by the

brake linings.

Checking s�oke tension

Warning

Brake discs - wear limit

Front

2.5 mm (0.098 in)

Rear

3.5 mm (0.138 in)

If the brake disc thickness is less than the specified value:

Change the brake disc.

Check the front and rear brake discs for damage, cracking and deformation.

If the brake disc shows signs of damage, cracking, or deformation:

Change the brake disc.

Danger of accidents

Instable handling due to incorrect spoke tension.

Ensure that the spoke tension is correct.

Info

A loose spoke can cause wheel imbalance, which leads to more loose spokes in a short time.

If the spokes are too tight, they can break due to local overload.

Check the spoke tension regularly, especially on a new motorcycle.

Tap each spoke with a screwdriver.

•

Info

The sound frequency depends on the length and thickness of the spoke.

If there are different sound frequencies in spokes with the same length and

thickness, this indicates different spoke tensions.

You should hear a high note.

If the spoke tension varies:

Correct the spoke tension.

Check the spoke torque.

Guideline

Spoke nipple, front wheel
Spoke nipple, rear wheel

M4.5

6 Nm (4.4 lbf ft)

M4.5

6 Nm (4.4 lbf ft)

Torque wrench with various accessories in set (58429094000) (or p. 260)

Содержание FE 350 2014
























































































































































































































































































Результаты поиска

Содержание FE 350 2014

Отзывы:

Husqvarna FE 350 2014, Руководство по ремонту, Страница: 89 / 279

Результаты поиска

Содержание FE 350 2014

Отзывы: