manualshive.com logo in svg

Husqvarna FE 350 2014, Руководство по ремонту, Страница: 90 / 279

Поделиться
Скачать
Husqvarna FE 350 2014 Скачать руководство пользователя страница 90

14 

WHEELS 

88 

14.5 

Front wheel 

14.5.1 

Removing the front wheel 

14.5.2 

Installing the front wheel 

Warning 

Preparatory work 

Raise the motorcycle with a lift stand.  (- p. 11) 

Main work 

Press the brake caliper onto the brake disc by hand in order to push back the 

brake pistons. 

•

Info

I 

Make sure when pushing back the brake pistons that you do not press the 

brake caliper against the spokes. 

Loosen screw 

O 

by several turns.

Release screws 

8. 

Press on screw 

O 

to push the wheel spindle out of the axle clamp.

Remove screw 

O. 

Hold the front wheel and remove the wheel spindle. Take the front wheel out of 

the fork. 

•

Info

I 

Do not pull the hand brake lever when the front wheel is removed. 

Always lay the wheel down in such a way that the brake disc is not dam­

aged. 

Remove spacers 

8. 

Danger of accidents 

Reduced braking efficiency due to oil or grease on the  brake discs. 

- Always keep the brake discs free of oil and grease, and clean them with brake cleaner when necessary.

Check the wheel bearing for damage and wear. 

If the wheel bearing is damaged or worn: 

-

Change the front wheel bearing.  (- p.  89)

Clean and grease the shaft seal rings 

Q 

and bearing surface 

6) 

of the spacers.

I 

Long-life grease (- p. 257)

Insert the spacers. 

Содержание FE 350 2014
























































































































































































































































































Отзывы:

Нет отзывов