Husqvarna FE 350 2014 Скачать руководство пользователя страница 158

Страница: 158 / 279

18 ENGINE

18.4.26 Checking the cylinder head

302805-10

302808-10

18.4.27 Installing the valves

302712-11

Check valve guides

using the special tool.

Limit plug gauge (77229026000) (or p. 264)

If the special tool is easy to insert in the valve guide:

Change the valve guide and valve.

156

Check the sealing area of the spark plug thread and the valve seats from damage

and cracking.

If there is damage or cracking:

Change the cylinder head.

Using a straightedge and the special tool, check the sealing area of the cylinder

for distortion.

Feeler gauge (590290411 00) (or p. 261)

Cylinder/cylinder head - distortion of

sealing area

:!> 0.10 mm (:!> 0.0039 in)

If the measured value does not meet specifications:

Change the cylinder head.

Check sealing seat

of the valves.

Valve - sealing seat width

Intake

Valve - sealing seat width

Exhaust

1.40 mm (0.0551 in)

1 .40 mm (0.0551 in)

If the measured value does not meet specifications:

Rework the valve seat.

Blow compressed air through all oil channels and check that they are clear.

Position valve spring seat

Mount valve stem seal

Mount the valve corresponding to its installation position.

Mount the valve spring with the tighter coil facing downward.

Mount the valve spring retainers.

Pre-tension the valve spring using the special tool.

Valve spring mounter (59029019000) (or p. 261)

Insert for valve spring lever (77229060000) (or p. 265)

Содержание FE 350 2014
























































































































































































































































































Результаты поиска

Содержание FE 350 2014

Отзывы:

Husqvarna FE 350 2014, Руководство по ремонту, Страница: 158 / 279

Результаты поиска

Содержание FE 350 2014

Отзывы: