Husqvarna FE 350 2014 Скачать руководство пользователя страница 116

Страница: 116 / 279

BRAKE SYSTEM

Changing the rear brake fluid

Warning
Skin irritation

Brake fluid can cause skin irritation on contact.

- Avoid contact with skin and eyes, and keep out of the reach of children.

Wear suitable protective clothing and goggles.

114

If brake fluid comes into contact with the eyes, flush the eyes thoroughly with water and consult a physician immediately.

Warning

Environmental hazard

Hazardous substances cause environmental damage.

Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.

Info

Avoid contact between brake fluid and painted parts. Brake fluid attacks paint!

Use only clean brake fluid from a sealed container.

Cover the painted parts.

Remove screw cap

with membrane and the O-ring.

Draw the old brake fluid out of the brake fluid reservoir using a syringe and fill

with fresh brake fluid.

Bleed syringe (50329050000) (or p. 259)
Brake fluid DOT 4 (or p. 256)

Mount bleeder cover

Bleeder cover (00029013006) (or p. 259)

Connect the bleeding device.

Bleeding device (00029013100) (or p. 259)

Open shut-off valve

fD.

•

Info

Follow the operating instructions of the bleeding device.

Ensure that the filling pressure is correctly set at pressure gauge 6). If neces

sary, adjust the filling pressure at pressure regulator

G,.

Guideline

Filling pressure

2 ... 2.5 bar (29 ... 36 psi)

Pull off protection cap

of the bleeder screw. Connect the hose of the bleeder

bottle.

Bleeding device (00029013100) (or p. 259)

Open bleeder screw

by approx. one-half turn.

•

Info

Bleed until new brake fluid emerges from the bleeder bottle hose without

bubbles.

Tighten the bleeder screw.

Close shut-off valve

fD.

Содержание FE 350 2014
























































































































































































































































































Результаты поиска

Содержание FE 350 2014

Отзывы:

Husqvarna FE 350 2014, Руководство по ремонту, Страница: 116 / 279

Результаты поиска

Содержание FE 350 2014

Отзывы: