Husqvarna FE 350 2014 Скачать руководство пользователя страница 58

Страница: 58 / 279

9.22

SHOCK ABSORBER, SWINGARM

Assembling the iston rod

201418-10

201420-10

Preparatory work

- Assemble the seal ring retainer. (

p. 55)

Main work

Clamp the piston rod with the fork in a vise.
Guideline

Use soft jaws.

Mount rubber buffer

and locking cap

Position special tool on the piston rod.

Mounting sleeve (T1215) (

p. 267)

Grease the dust boot and push seal ring retainer

onto the piston rod.

Lubricant (T625) (

p. 257)

Remove the special tool.

Mount rebound washer

with the cut-out facing downward.

Mount the compression shim stack

with the smaller shims facing downward.

Sand both sides of piston

on a surface plate using 1200-grit sandpaper.

Clean the piston.

- Assemble the piston.

Guideline

ViewO

Piston from above

ViewC,

Piston from below

Mount the rebound shim stack @ with the smaller shims facing upward.

Содержание FE 350 2014
























































































































































































































































































Результаты поиска

Содержание FE 350 2014

Отзывы:

Husqvarna FE 350 2014, Руководство по ремонту, Страница: 58 / 279

Результаты поиска

Содержание FE 350 2014

Отзывы: