manualshive.com logo in svg

Husqvarna FE 350 2014, Руководство по ремонту, Страница: 45 / 279

Поделиться
Скачать
Husqvarna FE 350 2014 Скачать руководство пользователя страница 45

9 

9.4 

SHOCK ABSORBER, SWINGARM 

Ad"ustin  the rebound dam  in  of the shock absorber 

Caution 
Danger of accidents 

Disassembly of pressurized parts can lead to injury. 

- The shock absorber is filled with high density nitrogen. Adhere to the description provided.

- Turn adjusting screw 

O 

clockwise up to the last perceptible click.

- Turn counterclockwise by the number of clicks corresponding to the shock

absorber type.

Guideline

Rebound damping 

Comfort 

20 clicks 

Standard 

18 clicks 

Sport 

16 clicks 

Info 

Turn clockwise to increase damping; turn counterclockwise to reduce 

damping. 

Measuring rear wheel sag unloaded 

Preparatory work 

-

Raise the motorcycle with a lift stand. (or  p. 11)

Main work 

-

Measure the distance - as vertically as possible - between the rear axle and a

fixed point such as a mark on the side cover.

-

Make note of the value as measurement 

G.

Finishing work 

-

Remove the motorcycle from the lift stand. (or  p. 11)

Checking the static sag of the shock absorber 

-

Measure distance 

G 

of rear wheel unloaded. (or  p. 43)

-

Hold the motorcycle upright with the aid of an assistant.

-

Measure the distance between the rear axle and the fixed point again.

-

Note down the value as dimension  G).

• 

Info

I 

The static sag is the difference between measurements 

G 

and  G).

-

Check the static sag.

I 

Static sag

130 mm (1.18 in)

If the static sag is less or more than the specified value: 

- Adjust the spring preload of the shock absorber. (or p. 44)

43 

Содержание FE 350 2014
























































































































































































































































































Отзывы:

Нет отзывов