Husqvarna FE 350 2014 Скачать руководство пользователя страница 28

Страница: 28 / 279

FORK, TRIPLE CLAMP

201732-11

-0-

6.22

Assemblin the cartrid e

•

Info

- Grind the piston on both sides on a surfacing plate using 1200 grit sandpaper.

- Clean the piston.

- Lubricate the piston ring.

Fork oil (SAE 4) (48601166S1) (or p. 256)

- Mount the piston with chamfer

facing down.

- Mount the rebound shim stack

with the smaller washers facing upward.

- Press the piston downward against the spring.

✓ The piston should not squeeze the shims.

- Position valve@ in the hydrostop needle@. Mount and tighten the hydrostop

needle.

Guideline

Hydrostop needle on piston rod

•

Info

M6x0.5

I 7 Nm (5.2 lbf ft)

I G

silver hydrostop needle on compression damping side.

red hydrostop needle on rebound damping side.

- Unclamp the piston rod.

The steps are identical for both fork legs.

201795-11

Preparatory work

- Assemble the seal ring retainer. (or p. 24)

- Assemble the piston rod. (or p. 25)

Main work

- Mount and grease seal rings

and O-ring @.

Lubricant (T158) (or p. 257)

- Mount and lubricate pilot bushings@).

Fork oil (SAE 4) (48601166S1) (or p. 256)

- Check the length of the reservoir spring.

Guideline

Reservoir spring length with preload

spacer

If the length is out of tolerance:

- Correct the preload spacers.

46 mm (1.81 in)

- Position the spring with the preload spacers in the reservoir.

Содержание FE 350 2014
























































































































































































































































































Результаты поиска

Содержание FE 350 2014

Отзывы:

Husqvarna FE 350 2014, Руководство по ремонту, Страница: 28 / 279

Результаты поиска

Содержание FE 350 2014

Отзывы: