Husqvarna FE 350 2014 Скачать руководство пользователя страница 54

Страница: 54 / 279

9.17

SHOCK ABSORBER, SWINGARM

201407-10

Remove washer

for seal ring

Remove washer

Remove dust boot.

Changing the ilot bushing

Preparatory work

Remove the spring. (.- p. 48)

Disassemble the damper. (.- p. 49)

Disassemble the piston rod. (.- p. 50)

Disassemble the seal ring retainer. (.- p. 51)

Main work

Press pilot bushing

out of seal ring retainer

with the special tool.

Press drift (T1504) (.- p. 269)

Slide the new pilot bushing

onto the special tool.

Press drift (T1504) (.- p. 269)

Position the pilot bushing in the seal ring retainer using the special tool.

Press drift (T1504) (.- p. 269)

Support seal ring retainer

with sleeve 6) of the special tool. Press the pilot

bushing all the way in.

Assembly tool (T150S) (.- p. 269)

Lubricate the special tool.

Shock absorber fluid (SAE 2.5) (50180751 S1) (.- p. 256)

Calibration pin (T1205) (.- p. 267)

Support seal ring retainer

with sleeve 6) of the special tool.

Assembly tool (T150S) (.- p. 269)

Press the special tool through the new pilot bushing.

Calibration pin (T1205) (.- p. 267)

✓ The pilot bushing is calibrated.

Finishing work

Assemble the seal ring retainer. (.- p. 55)

Содержание FE 350 2014
























































































































































































































































































Результаты поиска

Содержание FE 350 2014

Отзывы:

Husqvarna FE 350 2014, Руководство по ремонту, Страница: 54 / 279

Результаты поиска

Содержание FE 350 2014

Отзывы: