Husqvarna FE 350 2014 Скачать руководство пользователя страница 13

Страница: 13 / 279

5.1

MOTORCYCLE

Raising the motorc cle with a lift stand

401942-01

Note

Danger of damage

The parked vehicle may roll away or fall over.

- Always place the vehicle on a firm and even surface.

Raise the motorcycle at the frame underneath the engine.

Lift stand (81329955000) (,... p. 266)

✓ Neither wheel is in contact with the ground.

Secure the motorcycle against falling over.

5.2

Removin the motorc cle from the lift stand

Note

Danger of damage

The parked vehicle may roll away or fall over.

- Always place the vehicle on a firm and even surface.

5.3

Note

Starting

Danger
Danger of poisoning

401943-10

Remove the motorcycle from the lift stand.

Remove the lift stand.

To park the motorcycle, press side stand

to the ground with your foot and

lean the motorcycle on it.

•

Info

When you are riding, the side stand must be folded up and secured with

the rubber band.

Exhaust gases are toxic and inhaling them may result in unconsciousness and/or death.

When running the engine, always make sure there is sufficient ventilation, and do not start or run the engine in an

enclosed space without an effective exhaust extraction system.

Engine failure

High engine speeds in cold engines have a negative effect on the service life of the engine.

- Always warm up the engine at low engine speeds.

401944-11

400733-01

Raise the motorcycle off of the stand and secure the stand with the rubber

band

Shift transmission to neutral.

(FE 350 AU)

- Turn the emergency OFF switch to the position 0.

Condition

Ambient temperature: < 20 °C (< 68 °F)

Pull the idle speed adjusting screw all the way out.

Press the electric starter button.

•

Info

Press the electric starter button for at most 5 seconds. Wait for a least 5

seconds before trying again.

Warning lamp Fl lights up briefly as a functional control when starting.

Содержание FE 350 2014
























































































































































































































































































Результаты поиска

Содержание FE 350 2014

Отзывы:

Husqvarna FE 350 2014, Руководство по ремонту, Страница: 13 / 279

Результаты поиска

Содержание FE 350 2014

Отзывы: