28
SERVICE SCHEDULE
28.1
Service schedule
210
Every 30 operating hours/after every race
Every 15 operating hours
Once after 1 operating hour
Read out the fault memory using the Husqvarna Motorcycles diagnostics tool.
0
•
I
•
Check that the electrical equipment is functioning properly.
0
•
I
•
Check and charge the battery.
•
I
•
I
I
Check the front brake linings. (- p. 104)
I
I
•
I
•
Check the rear brake linings. (- p. 109)
I
I
•
I
•
Check the brake discs. (- p. 87)
I
I
•
I
•
Check the brake lines for damage and leakage.
I
I
•
I
•
Check the rear brake fluid level. (- p. 112)
I
I
•
I
•
Check the free travel of the foot brake lever. (- p. 111)
I
I
•
I
•
Check the frame and swingarm.
I
I
•
I
•
Check the swingarm bearing.
I
I
I
•
Check the shock absorber linkage.
I
I
•
I
•
Check the heim joints at the top of the shock absorber.
•
I
•
Check the tire condition. (- p. 86)
0
•
I
•
Check the tire air pressure. (- p. 86)
0
•
I
•
Check the wheel bearing for play.
I
I
•
I
•
Check the wheel hubs.
•
I
•
Check the rim run-out.
0
•
I
•
Check the spoke tension. (- p. 87)
0
•
I
•
Check the chain, rear sprocket, motor sprocket, and chain guide. (- p. 94)
•
I
•
Check the chain tension. (- p. 93)
0
•
I
•
Grease all moving parts (e.g., side stand, hand lever, chain, ... ) and check for smooth operation.
•
I
•
I
Check/rectify the fluid level of the hydraulic clutch. (- p. 187)
I
I
•
I
•
Check the front brake fluid level. (- p. 107)
I
I
•
I
•
Check the free travel of the hand brake lever. (- p. 106)
•
I
•
Check the steering head bearing play. (- p. 35)
0
•
I
•
Check the valve clearance.
0
I
•
Check the clutch.
I
•
I
I
Change the shaft seal rings of the water pump.
I
•
Change the engine oil and oil filter, clean the oil screen. (- p. 192)
0
•
I
•
Check all hoses (e. g., fuel, cooling, bleeding, drainage) and sleeves for cracking, leaks, and incorrect routing.
0
•
I
•
Check the antifreeze and coolant level. (- p. 188)
I
0
I
•
I
•
Check the cables for damage and routing without sharp bends.
•
I
•
Check that the cables are undamaged, routed without sharp bends and set correctly.
0
•
I
•
Clean the air filter and air filter box.
•
I
•
I
I
Change the glass fiber yarn filling of the main silencer. (- p. 71)
I
I
I
•
Check the screws and nuts for tightness.
0
•
I
•
Check the headlight setting. (- p. 118)
0
•
I
•
Change the fuel screen. (- p. 79)
0
•
I
•
Check the fuel pressure. (- p. 82)
•
I
•
Adjust the idle speed. (- p. 200)
0
•
I
•
Check that the radiator fan is functioning properly.
0
•
I
•
Final check: Check the vehicle for roadworthiness and take a test ride.
0
•
I
•
Read out the fault memory after the test ride using the Husqvarna Motorcycles diagnostics tool.
0
•
I
•
Make the service entry in the
Husqvarna Motorcycles Dealer.net
and in the Service and Warranty Booklet.
0
•
I
•
Содержание FE 350 2014
Страница 2: ......
Страница 241: ...29 WIRING DIAGRAM Components A11 EFI control unit 832 Fuel level indicator F1 Fuse P13 Speedometer 239 ...
Страница 253: ...29 WIRING DIAGRAM Components A11 EFI control unit 832 Fuel tank sensor F1 Fuse P13 Speedometer 251 ...
Страница 272: ...32 SPECIAL TOOLS 270 Nitro en filling tool Art no T170S1 2x 3x T170S1 H00855 01 ...