Husqvarna FE 350 2014 Скачать руководство пользователя страница 20

Страница: 20 / 279

FORK, TRIPLE CLAMP

Unclamp the fork leg.

Push the outer tube down. Drain the fork oil.

Clamp the fork leg with the axle clamp.

Release hydrostop unit

and remove it.

•

Info

Do not use an impact wrench.

Place a pan underneath since oil will run out.

Remove the cartridge from the fork leg.

Press-out tool (T1 4051) (- p. 269)

•

Info

Removing the O-ring seat from the cartridge usually requires the applica

tion of force.

Remove dust boot

Remove fork protection ring f).

•

Info

The fork protection ring does not necessarily need to be removed for

repair work.

Remove lock ring @.

•

Info

The lock ring has a ground end against which a screwdriver can be posi

tioned.

Warm the outer tube in area C5) of the lower sliding bushing.

Guideline

(122 °F)

Pull the outer tube forcefully off of the inner tube.

Info

The lower sliding bushing

must be pulled out of its bearing seat.

Содержание FE 350 2014
























































































































































































































































































Результаты поиска

Содержание FE 350 2014

Отзывы:

Husqvarna FE 350 2014, Руководство по ремонту, Страница: 20 / 279

Результаты поиска

Содержание FE 350 2014

Отзывы: