manualshive.com logo in svg

Husqvarna FE 350 2014, Руководство по ремонту, Страница: 202 / 279

Поделиться
Скачать
Husqvarna FE 350 2014 Скачать руководство пользователя страница 202

24 

24.2 

THROTTLE VALVE  BODY 

200 

Ad"ustin  the idle s  eed 

Warning 

Danger of accidents 

The engine may go out spontaneously if the idle speed is set too low. 

-

Set the idle speed to the specified value.

Danger 

Danger of poisoning 

Exhaust gases are toxic and inhaling them may 

result in unconsciousness and/or death. 
-

When running the engine, always make sure there is sufficient ventila­

tion, and do not start or run the engine in an enclosed space without

an effective exhaust extraction system.

Run the engine warm and push idle speed adjusting screw 

O 

all the way in.

Set the idle speed by turning the idle speed adjusting screw. 
Guideline 

Executing the initialization run 

Idle speed 

•

Info

I 

2,050 ... 2,150 rpm

I 

Turn counterclockwise to increase the idle speed. 

Turn clockwise to decrease the idle speed. 

Condition 

The diagnostics tool is connected and running. 

Execute 

"Engine electronics"> "Functions"> "Delete adaptation values". 

✓ The adaptation values are deleted.

Select 

"Engine electronics" > "Measured values" > "Coolant temperature 

sensor (TW1)". 

✓ The coolant temperature is displayed during the initialization run.

Danger 

Danger of poisoning 

Exhaust gases are toxic and inhaling them may 

result in unconsciousness and/or death. 
-

When running the engine, always make sure there is sufficient ventila­

tion, and do not start or run the engine in an enclosed space without

an effective exhaust extraction system.

Start the engine without operating the throttle grip. 
Guideline 

I 

Coolant temperature

I 

< 25 °C (< 77 °F)

Let the engine idle until it reaches the specified temperature. 
Guideline 

I 

Coolant temperature

•

Info

I 

80 ... 90 °C (176 ... 194  °F)

I 

Do not operate the throttle grip during the initialization process. 

As soon as the specified temperature is reached, switch off the ignition. 

•

Info

I 

If the initialization is not completed or the initialization process is inter­

rupted, the entire process must be restarted. 

Содержание FE 350 2014
























































































































































































































































































Отзывы:

Нет отзывов