Husqvarna FE 350 2014 Скачать руководство пользователя страница 76

Страница: 76 / 279

11.5

11.6

AIR FILTER

Insert both parts together, position them, and secure them using air filter

holder

in area

C,.

✓ The arrow of marking UP faces up.

•

Info

If the air filter is not mounted correctly, dust and dirt may enter the engine

and result in damage.

Finishing work

Install the air filter box cover. (

p. 73)

Cleaning the air filter and air filter box

Warning

Environmental hazard

Hazardous substances cause environmental damage.

Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.

Info

Do not clean the air filter with fuel or petroleum since these substances attack the foam.

Sealing the air filter box

401559-01

Preparatory work

Remove the air filter box cover. (

p. 73)

Remove the air filter. (

p. 73)

Main work

Wash the air filter thoroughly in special cleaning liquid and allow it to dry properly.

Air filter cleaning agent (

p. 257)

•

Info

Only press the air filter to dry it, never wring it out.

Oil the dry air filter with a high quality filter oil.

Oil for foam air filter(

p. 257)

Clean the air filter box.

Check the intake flange for damage and looseness.

Finishing work

Install the air filter. (

p. 73)

Install the air filter box cover. (

p. 73)

Preparatory work

Remove the air filter box cover. (

p. 73)

Main work

Seal the air filter box in the marked area f).

Finishing work

Install the air filter box cover. (

p. 73)

Содержание FE 350 2014
























































































































































































































































































Результаты поиска

Содержание FE 350 2014

Отзывы:

Husqvarna FE 350 2014, Руководство по ремонту, Страница: 76 / 279

Результаты поиска

Содержание FE 350 2014

Отзывы: