Husqvarna FE 350 2014 Скачать руководство пользователя страница 38

Страница: 38 / 279

6.31

FORK, TRIPLE CLAMP

G01808-10

Remove the upper bearing race @ using a suitable tool.

Press in the new bearing race all the way using a suitable tool.

Pull off bearing

Remove seal ring retainer.

Remove O-ring.

Grease the new O-ring and mount with seal ring retainer.

Press on the new bearing with a suitable tube as far as it will go.

Finishing work

Install the lower triple clamp. ('r p. 32)

Install the front fender.

(,r

p. 84)

Install the front wheel.

(,r

p. 88)

Install the headlight mask with the headlight.

(,r

p. 85)

Check that the wiring harness, throttle cables and brake and clutch lines can

move freely and are routed correctly.

Check the steering head bearing play.

(,r

p. 35)

Remove the motorcycle from the lift stand.

(,r

p. 11)

Check the headlight setting.

(,r

p. 118)

Adjusting the �la� of the steering head bearing

Preparatory work

Raise the motorcycle with a lift stand.

(,r

p. 11)

Main work

Loosen screws

Remove screw

Loosen and retighten screw

Guideline

Screw, top steering head

M20x1.5

12 Nm (8.9 lbf ft)

Using a plastic hammer, tap lightly on the upper triple clamp to avoid strains.

Tighten screws

Guideline

Screw, top triple clamp

17 Nm (12.5 lbf ft)

Mount and tighten screw @.

Guideline

Screw, top steering stem

17 Nm

(12.5 lbf ft)

Loctite

243

™

Содержание FE 350 2014
























































































































































































































































































Результаты поиска

Содержание FE 350 2014

Отзывы:

Husqvarna FE 350 2014, Руководство по ремонту, Страница: 38 / 279

Результаты поиска

Содержание FE 350 2014

Отзывы: