Husqvarna FE 350 2014 Скачать руководство пользователя страница 121

Страница: 121 / 279

17.7

LIGHTING SYSTEM, INSTRUMENTS

Ad"usting the headlight range

If the light-dark border does not meet specifications:

- Adjust the headlight range.

(,r

p. 119)

Preparatory work

Check the headlight setting. (or p. 118)

Main work

- Adjust the headlight range of the headlight by turning adjusting screw

Guideline

119

The boundary between light and dark must be exactly on the lower mark for

a motorcycle with driver (instructions on how to apply the mark: Checking the

headlight setting).

•

Info

Turn clockwise to reduce the headlight range; turn counterclockwise to

increase the headlight range.

A change in weight on the vehicle may require a correction of the headlight

range.

Содержание FE 350 2014
























































































































































































































































































Результаты поиска

Содержание FE 350 2014

Отзывы:

Husqvarna FE 350 2014, Руководство по ремонту, Страница: 121 / 279

Результаты поиска

Содержание FE 350 2014

Отзывы: