HP StorageWorks X9720 Скачать руководство пользователя страница 139

Страница: 139 / 187

IMPORTANT:

Configure a passive agile management console only if the agile management

console is enabled and an active agile management console is configured.

If you configured a user network, enter a VIF IP address and netmask for the network.

If you configured a passive management console, enter the following command to verify the
status of the console:

ibrix_fm -i

IMPORTANT:

Next, go to

“Completing the restore on a file serving node” (page 129)

Configuring the management console on the dedicated (non-agile)
Management Server blade

This procedure is intended for systems that are not using the agile management console
configuration, and instead, the standard management console is configured on the Management
Server blade.

To configure the management console, complete the following steps:

Configuring the management console on the dedicated (non-agile) Management Server blade

139

Содержание StorageWorks X9720




























































































































































































Результаты поиска

Содержание StorageWorks X9720

Отзывы:

Похожие инструкции для StorageWorks X9720

Бренды по названию

Популярные бренды

HP StorageWorks X9720, Руководство администратора

Результаты поиска

Содержание StorageWorks X9720

Отзывы:

Похожие инструкции для StorageWorks X9720

Бренды по названию

Популярные бренды