HP StorageWorks X9720 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 187

background image

8 Monitoring cluster operations

Monitoring the X9720 Network Storage System status

The X9720 storage monitoring function gathers X9720 system status information and generates
a monitoring report. The X9000 management console displays status information on the dashboard.
This section describes how to the use the CLI to view this information.

Monitoring intervals

The monitoring interval is set by default to 15 minutes (900 seconds). You can change the interval
setting by using the following command to change the <

interval_in_seconds

> variable:

ibrix_host_tune -C

vendorStorageHardwareMonitoringReportInterval=<interval_in_seconds>

NOTE:

The storage monitor will not run if the interval is set to less than 10 minutes.

Viewing storage monitoring output

Use the following command to view the status of the X9720 system:

ibrix_vs -i -n <storagename>

To obtain the storage name, run the

ibrix_vs -l

command. For example:

# ibrix_vs -l
NAME TYPE IP PROXYIP
----- ---- ---------- -------
x303s exds 172.16.1.1

Monitoring the status of file serving nodes

The dashboard on the management console GUI displays information about the operational status
of file serving nodes, including CPU, I/O, and network performance information.

To view status from the CLI, use the

ibrix_server -l

command. This command provides CPU,

I/O, and network performance information and indicates the operational state of the nodes, as
shown in the following sample output:

<installdirectory>/bin/ibrix_server -l

SERVER_NAME STATE CPU(%) NET_IO(MB/s) DISK_IO(MB/s) BACKUP HA
----------- ------------ ------ ------------ ------------- ------ --
node1 Up, HBAsDown 0 0.00 0.00 off
node2 Up, HBAsDown 0 0.00 0.00 off

Monitoring the X9720 Network Storage System status

49

«
...
47
48
49
50
51
...
»

Содержание StorageWorks X9720




























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для StorageWorks X9720

Бренд: Parker Страницы: 344

Бренд: Juniper Страницы: 502

Бренд: Falcon Страницы: 24

3C410012A - OfficeConnect Remote 531 Access...

Бренд: 3Com Страницы: 72

Бренд: Intellinet Страницы: 2

Бренд: ekwb Страницы: 2

Бренд: Radicom Страницы: 27

Бренд: XJTAG Страницы: 9

Бренд: Xilinx Страницы: 8

Бренд: Lantech Страницы: 40

Бренд: Intel Страницы: 26

CNPS7000C Series

Бренд: ZALMAN Страницы: 8

Zypad WL15 Series

Бренд: Eurotech Страницы: 2

Бренд: Aaeon Страницы: 72

Бренд: TP-Link Страницы: 131

Бренд: Omron Страницы: 6

IPS Pro-Module-24C-GE-BP-TM

Бренд: Trend Micro Страницы: 3

Бренд: Patton electronics Страницы: 145

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды