HP StorageWorks X9720 Скачать руководство пользователя страница 25

Страница: 25 / 187

FTP.

When you add an FTP share on the Add FTP Shares dialog box or with the

ibrix_ftpshare

command, specify the VIF as the IP address that clients should use to access the share.

HTTP.

When you create a virtual host on the Create Vhost dialog box or with the

ibrix_httpvhost

command, specify the VIF as the IP address that clients should use to access

shares associated with the Vhost.

X9000 clients.

Use the following command to prefer the appropriate user network. Execute the

command once for each destination host that the client should contact using the specified interface.

ibrix_client -n -h SRCHOST -A DESTNOST/IFNAME

For example:

ibrix_client -n -h client12.mycompany.com -A ib50-81.mycompany.com/bond1

NOTE:

Because the backup NIC cannot be used as a preferred network interface for X9000

clients, add one or more user network interfaces to ensure that HA and client communication work
together.

Support for link state monitoring

Do not configure link state monitoring for user network interfaces or VIFs that will be used for CIFS
or NFS. Link state monitoring is supported only for use with iSCSI storage network interfaces, such
as those provided with X9300 Gateway systems.

Support for link state monitoring

Содержание StorageWorks X9720




























































































































































































Результаты поиска

Содержание StorageWorks X9720

Отзывы:

Похожие инструкции для StorageWorks X9720

Бренды по названию

Популярные бренды

HP StorageWorks X9720, Руководство администратора

Результаты поиска

Содержание StorageWorks X9720

Отзывы:

Похожие инструкции для StorageWorks X9720

Бренды по названию

Популярные бренды