HP StorageWorks X9720 Скачать руководство пользователя страница 75

Страница: 75 / 187

Confirm that automated failover is enabled:

<ibrixhome>/bin/ibrix_server -l

In the output,

should display

From the node hosting the active management console, perform a manual backup of the
upgraded configuration:

<ibrixhome>/bin/ibrix_fm -B

Upgrade X9000 clients:

•

For Linux clients, see

“Upgrading Linux X9000 clients” (page 75)

•

For Windows clients, see

“Upgrading Windows X9000 clients” (page 75)

Verify that all version indicators match for file serving nodes and X9000 clients. Run the
following command from the active management console:

<ibrixhome>/bin/ibrix_version –l

If there is a version mismatch, run the

/ibrix/ibrixupgrade -f

script again on the

affected node, and then recheck the versions. The installation is successful when all version
indicators match. If you followed all instructions and the version indicators do not match,
contact HP Support.

Verify the health of the cluster:

<ibrixhome>/bin/ibrix_health -l

The output should show

Passed / on

For an agile configuration, on all nodes hosting the passive management console, return the
management console to passive mode:

<ibrixhome>/bin/ibrix_fm -m passive

10.

If you received a new license from HP, install it as described in the “Licensing” chapter in this
document.

11.

Upgrade firmware on X9720 systems. See

“Upgrading firmware on X9720 systems” (page 76)

Upgrading Linux X9000 clients

Be sure to upgrade the management console and file serving nodes before upgrading Linux X9000
clients. Complete the following steps on each client:

Expand the upgrade tarball or mount the upgrade DVD.

Run the upgrade script:

./ibrixupgrade -f

The upgrade software automatically stops the necessary services and restarts them when the
upgrade is complete.

Execute the following command to verify the client is running X9000 Software:

/etc/init.d/ibrix_client status
IBRIX Filesystem Drivers loaded
IBRIX IAD Server (pid 3208) running...

The

IAD

service should be running, as shown in the previous sample output. If it is not, contact HP

Support.

Upgrading Windows X9000 clients

Complete the following steps on each client:

Upgrading Linux X9000 clients

Содержание StorageWorks X9720




























































































































































































Результаты поиска

Содержание StorageWorks X9720

Отзывы:

Похожие инструкции для StorageWorks X9720

Бренды по названию

Популярные бренды

HP StorageWorks X9720, Руководство администратора

Результаты поиска

Содержание StorageWorks X9720

Отзывы:

Похожие инструкции для StorageWorks X9720

Бренды по названию

Популярные бренды