HP StorageWorks X9720 Скачать руководство пользователя страница 2

Страница: 2 / 187

Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial

Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under

vendor's standard commercial license.

The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express

warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall

not be liable for technical or editorial errors or omissions contained herein.

Acknowledgments

Microsoft® and Windows® are U.S. registered trademarks of Microsoft Corporation.

UNIX® is a registered trademark of The Open Group.

Warranty

WARRANTY STATEMENT: To obtain a copy of the warranty for this product, see the warranty information website:

http://www.hp.com/go/storagewarranty

Revision History

Description

Software

Version

Date

Edition

Initial release of the X9720 Network Storage System.

5.3.1

December 2009

First

Added network management and Support ticket.

5.4

April 2010

Second

Added management console backup, migration to an agile management
console configuration, software upgrade procedures, and system recovery
procedures.

5.4.1

August 2010

Third

Revised upgrade procedure.

5.4.1

August 2010

Forth

Added information about NDMP backups and configuring virtual interfaces,
and updated cluster procedures.

5.5

December 2010

Fifth

Updated segment evacuation information.

5.5

March 2011

Sixth

Revised upgrade procedure.

5.6

April 2011

Seventh

Содержание StorageWorks X9720




























































































































































































Результаты поиска

Содержание StorageWorks X9720

Отзывы:

Похожие инструкции для StorageWorks X9720

Бренды по названию

Популярные бренды

HP StorageWorks X9720, Руководство администратора

Результаты поиска

Содержание StorageWorks X9720

Отзывы:

Похожие инструкции для StorageWorks X9720

Бренды по названию

Популярные бренды