HP StorageWorks X9720 Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 187

background image

14 Upgrading firmware

IMPORTANT:

The X9720 system is shipped with the correct firmware and drivers. Do not upgrade

firmware or drivers unless the upgrade is recommended by HP Support or is part of an X9720
patch provided on the HP web site.

Firmware update summary

When the X9720 Network Storage System software is first loaded, it automatically updates the
firmware for some components. The following table describes the firmware actions and status for
each component.

Update implications on system

operations

Summary of update process

Component

Requires reboot of server (one at a
time).

Update RPM, then reboot.

Server blade BIOS

Requires reboot of server (one at a
time).

Update RPM, then reboot.

E200i firmware

Requires reboot of server (one at a
time).

Update RPM, then reboot.

E410i

Requires reboot of server (one at a
time).

Update RPM, then reboot.

P700m firmware

Requires reboot of server (one at a
time).

Update RPM, then reboot.

iLO firmware

Updates while system is running. OA
reboots, but backup OA maintains
operations.

Update RPM, then update using the
OA CLI.

OA firmware

Requires complete system shutdown.

Update RPM, then update using the
OA CLI.

Virtual Connect (VC) firmware

Requires complete system shutdown.

Update RPM. Run online.

X9700c controller firmware HP and
X9700c management (SEP) firmware

Requires complete system shutdown.

Update RPM. Run online.

X9700cx I/O Controller firmware

Requires complete system shutdown.

Update RPM, then update using the
OA CLI.

SAS switch firmware

Requires complete system
shutdown.

Note:

For individual

out-of-revision drives, return to HP.

Update RPM. Run online.

Capacity block disk drive firmware

Locating firmware

Obtain the firmware by one of the following methods:

•

HP technical support might send you an updated mxso-firmware RPM. This installs firmware
in

/opt/hp/mxso/firmware

. This RPM also updates the revision information used by the

exds_stdiag

commands. The

README.txt

file in the directory tells you which file belongs

to which firmware. The files listed in the

README.txt

file are symlinks to the actual firmware

file. See the following table for a list of the symlinks.

•

HP technical support might send you a specific firmware file. Install this in the

/opt/hp/mxso/firmware

directory.

•

HP technical support might ask you to download a file from

www.hp.com

. Install this in the

/opt/hp/mxso/firmware

directory.

Firmware update summary

89

«
...
87
88
89
90
91
...
»

Содержание StorageWorks X9720




























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для StorageWorks X9720

Verizon DSL-2750B

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 4

Бренд: C&H Technologies Страницы: 46

Бренд: Paradyne Страницы: 112

Бренд: Cambium Networks Страницы: 215

Бренд: Falcon Страницы: 24

AXP-100H MUSCLE

Бренд: Thermalright Страницы: 36

Бренд: iCEBOX Страницы: 57

Бренд: Patton electronics Страницы: 9

Бренд: Qlogic Страницы: 8

Бренд: ZALMAN Страницы: 5

RouterBOARD 411R

Бренд: 4gon Страницы: 2

Бренд: Gira Страницы: 6

Бренд: B&B Electronics Страницы: 2

Бренд: Aaeon Страницы: 72

Бренд: ZALMAN Страницы: 9

airMAX NanoBridge M NBM3

Бренд: Ubiquiti Страницы: 24

SmartRack SR25UBEXP

Бренд: Tripp Lite Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды