HP StorageWorks X9720 Скачать руководство пользователя страница 125 | Manualshive

Страница: 125 / 187

background image

17 Recovering the X9720 Network Storage System

The instructions in this section are necessary in the following situations:

•

The X9720 fails and must be recovered.

•

A server blade is added or replaced.

•

The dedicated X9000 management console blade fails and must be replaced.

•

A file serving node fails and must be replaced.

You will need to create a QuickRestore DVD, as described later, and then install it on the affected
blade. This step installs the operating system and X9000 Software on the blade and launches a
configuration wizard.

CAUTION:

The Quick Restore DVD restores the file serving node to its original factory state. This

is a destructive process that completely erases all of the data on local hard drives.

CAUTION:

Recovering the management console node can result in data loss if improperly

performed. Contact HP Support for assistance in performing the recovery procedure.

Starting the recovery

To recover a failed blade, follow these steps:

1.

If a NIC monitor is configured on the user network, remove the monitor. To determine if NIC
monitoring is configured, run the following command on the Management Server:

ibrix_nic -i -h <hostname>

Check the output for a line such as the following:

Monitored By : titan16

To remove the monitor, use the following command:

ibrix_nic -m -h MONITORHOST -D DESTHOST/IFNAME

For example:

ibrix_nic -m -h titan16 -D titan15/eth2

2.

Obtain the latest Quick Restore image from the HP kiosk

http://www.software.hp.com/kiosk

(you will need your HP-provided login credentials).

3.

Burn the ISO image to a DVD.

4.

Insert the Quick Restore DVD into a USB DVD drive cabled to the Onboard Administrator or
to the Dongle connecting the drive to the front of the blade.

IMPORTANT:

Use an external USB drive that has external power; do not rely on the USB

bus for power to drive the device.

5.

Restart the server to boot from the DVD-ROM.

6.

When the following screen appears, enter

qr

to start the recovery.

Starting the recovery

125

«
...
123
124
125
126
127
...
»

Содержание StorageWorks X9720




























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для StorageWorks X9720

Бренд: D-Link Страницы: 11

Бренд: D-Link Страницы: 8

AirPlus DWL-810

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 84

Бренд: Hal Communications Страницы: 25

Бренд: TP-Link Страницы: 73

Бренд: Maxim Страницы: 26

Бренд: NetComm Страницы: 3

Бренд: Aztech Страницы: 2

Бренд: Qixiang Technology Страницы: 16

Бренд: Watchguard Страницы: 40

Marconi OMS 1200

Бренд: Ericsson Страницы: 136

Бренд: Tandy Страницы: 24

Бренд: Solwise Страницы: 7

Бренд: Ubiquiti Страницы: 23

Бренд: Omron Страницы: 29

Бренд: ZyXEL Communications Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды