HP StorageWorks X9720 Скачать руководство пользователя страница 90 | Manualshive

Страница: 90 / 187

background image

The following table maps firmware files to components. The actual system details may vary.

Symlink name in /opt/hp/mxso/firmware

Component

sbdisk_scexe

Disk drive

exds9100cx_scexe

X9700cx I/O controller

exds9100c_scexe

X9700c (management (SEP) and X9700c
controller firmware)

oa_fw

OA firmware

SASsw_scexe

SAS switch

SASsw_mp_fw

SAS switch management (Solex)

sbdisk_loc_scexe

Server blade local disk

Upgrading Onboard Administrator

1.

Download the X9720 Network Storage System

mxso-firmware

RPM. Install the

mxso-firmware

RPM on all servers.

2.

Get the IP address of the Onboard Administrator. For example on a system called

glory

,

look for an entry called

glory-mp in /etc/hosts

.

You also need a username and password for the Onboard Administrator. You can use the

exds

or

Administrator

username. The password for the Administrator user is located on

a label on OA 1.

3.

Run the following command:

# exds_update_oa_firmware

4.

The command prompts for IP address, username and password. Use the data from step 2:

HP Onboard Administrator Firmware Flash Utility v1.0.5
Copyright (c) 2009 Hewlett Packard Development Company, L.P.

OA network address:192.172.1.1
Username:exds
Password:****

The command automatically updates both Onboard Administrators, resetting each in turn as
appropriate.

Upgrading all Virtual Connect modules

The Virtual Connect firmware upgrade process updates all Virtual Connect modules at once. During
the update any single NIC (non-bonded) interfaces will lose network connectivity during the update.

NOTE:

This procedure assumes that the management network is using a bonded configuration

(that is, bond0 exists). If the system was originally installed with V1.0 software and subsequently
upgraded, the management network might not be bonded. If so, shut down all servers except
server 1 before using this procedure.

1.

Download and install the mxso-firmware RPM on all servers.

2.

Copy the firmware file (

vc_fw

) so it can be accessed by a non-root user. This example uses

the

ibrix

user. However, any other user could be used. You need to know the password of

the chosen user. The following commands copy the file in an appropriate way:

# cp /opt/hp/mxso/firmware/SASsw_mp_fw /home/ibrix

# chown ibrix.ibrix /home/ibrix/vc_fw

90

Upgrading firmware

«
...
88
89
90
91
92
...
»

Содержание StorageWorks X9720




























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для StorageWorks X9720

Netlink FRX4000

Бренд: Cabletron Systems Страницы: 8

Бренд: Cabletron Systems Страницы: 4

MMAC-Plus 9F106-02

Бренд: Cabletron Systems Страницы: 7

Бренд: Icidu Страницы: 10

Бренд: Xinje Страницы: 57

SAFETank Series

Бренд: Raidon Страницы: 49

Бренд: Zhone Страницы: 7

Бренд: Zhone Страницы: 1

Бренд: DPtech Страницы: 39

Бренд: KPN Страницы: 14

MegaRAID SCSI 320-2X

Бренд: LSI Страницы: 4

Бренд: Fostex Страницы: 20

SuperServer 5019S-L

Бренд: Supermicro Страницы: 61

Бренд: Time domain Страницы: 64

Бренд: Wintech Страницы: 21

PoleVault System A/V Source Inputs

Бренд: Extron electronics Страницы: 4

Бренд: Renesas Страницы: 941

Бренд: 8level Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды