HP StorageWorks X9720 Скачать руководство пользователя страница 169 | Manualshive

Страница: 169 / 187

background image

WARNING!

Power supplies or systems marked with these symbols indicate the presence of multiple sources of
power.

WARNING!

Any product or assembly marked with these symbols indicates that the component exceeds the
recommended weight for one individual to handle safely.

Weight warning

WARNING!

The device can be very heavy. To reduce the risk of personal injury or damage to equipment:

•

Remove all hot-pluggable power supplies and modules to reduce the overall weight of the
device before lifting.

•

Observe local health and safety requirements and guidelines for manual material handling.

•

Get help to lift and stabilize the device during installation or removal, especially when the
device is not fastened to the rails. When a device weighs more than 22.5 kg (50 lb), at least
two people must lift the component into the rack together. If the component is loaded into the
rack above chest level, a third person must assist in aligning the rails while the other two
support the device.

Rack warnings and precautions

Ensure that precautions have been taken to provide for rack stability and safety. It is important to
follow these precautions providing for rack stability and safety, and to protect both personnel and
property. Follow all cautions and warnings included in the installation instructions.

WARNING!

To reduce the risk of personal injury or damage to the equipment:

•

Observe local occupational safety requirements and guidelines for heavy equipment handling.

•

Obtain adequate assistance to lift and stabilize the product during installation or removal.

•

Extend the leveling jacks to the floor.

•

Rest the full weight of the rack on the leveling jacks.

•

Attach stabilizing feet to the rack if it is a single-rack installation.

•

Ensure the racks are coupled in multiple-rack installations.

•

Fully extend the bottom stabilizers on the equipment. Ensure that the equipment is properly
supported/braced when installing options and boards.

•

Be careful when sliding rack components with slide rails into the rack. The slide rails could
pinch your fingertips.

•

Ensure that the rack is adequately stabilized before extending a rack component with slide
rails outside the rack. Extend only one component at a time. A rack could become unstable
if more than one component is extended for any reason.

Weight warning

169

«
...
167
168
169
170
171
...
»

Содержание StorageWorks X9720




























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для StorageWorks X9720

Бренд: EAW Страницы: 2

Бренд: CAME Страницы: 19

Бренд: E-Lins Страницы: 59

Бренд: E-Lins Страницы: 11

Бренд: E-Lins Страницы: 9

Бренд: E-Lins Страницы: 5

Network Video Recorders

Бренд: e-Line Technology Страницы: 34

Бренд: ICP DAS USA Страницы: 8

Бренд: Watchguard Страницы: 24

Бренд: Paradyne Страницы: 112

Бренд: Cambium Networks Страницы: 215

Бренд: Matrix Switch Corporation Страницы: 61

USB-BRIDGEV2-EVAL

Бренд: IDT Страницы: 11

Speedway Revolution

Бренд: impinj Страницы: 60

Бренд: Marani Страницы: 39

Бренд: Asante Страницы: 150

Бренд: Giacomini Страницы: 2

Бренд: A4Tech Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды