
36
ADP200 • Quick installation guide - Specifications and connection
Note!
In this version, terminals 11 (0V I/O) and 12 (24V I/O) can be used only to power external circuits with the +24 volts generated by the ADP. Connecting an
external 24 volt power supply to these terminals has no effect because the control card cannot be powered with external voltage.
7.2.2.2 Terminal strip and connection ADP200-...-24 models
6 digital inputs (DI) + 1 Enable input (EN-HW) + 1 motor protection input (MO) + 2 digital outputs (DO) + 3 analog
inputs (AI) + 1 analog outputs (AO) + 2 relay outputs (RO).
Note!
+24Vdc voltage, which is used to externally supply the regulation card has to be stabilized and with a maximum ±10% tolerance. The maximum absorption
is 1A. It is not suitable to power supply the regulation card only through a unique rectifier and capacitive filter.
If the control is powered with a +24V external, you have to insert a protective diode as described in "Figure 7.3.1.6: External diode on +24V external".
7.2.2.3 Terminal strip and connection ADP200-...-I01 models
8 digital inputs (DI) + 1 Enable input (EN-HW) + 1 motor protection input (MO) + 2 digital outputs (DO) + 3 analog
inputs (AI) + 2 relay outputs (RO).
EXP-IO-D10A3R2-ADP
T3
T2
T1
Commands
Associated parameter
+ 24V (from PLC)
Fault State (to PLC)
+ 24V (from PLC)
Drive R
eady (to PLC)
Associated parameter
Motor protection input
Motor protection input
Analog input 2X
Analog input 2X
Analog input 1X
Analog input 1X
Analog input 1 (Sensor)
Commands
Associated parameter
Fault R
eset (from PLC)
Start (from PLC)
Enable (from PLC)
RO
2O
RO
2C
RO
1O
RO
1C
DO
2
DO
1
DO
PS PE
MO1
-
MO1
+
AI
2–
AI
2+
AI
1–
AI
1+
AIS
IN+
AIS
24V
AIS
0V PE
DI
8
DI
7
DI
6
DI
5
DI
4
DI
3
DI
2
DI
1
EN
HW
DIO
CM
0V
I/O
24V
I/O
54 55 56 57 26 27 29 99
80 81 40 41 42 43 70 71 72 99
1
2
3
4
5
6
7
8
9 10 11 12
Note!
In this version, terminals 11 (0V I/O) and 12 (24V I/O) can be used only to power external circuits with the +24 volts generated by the ADP. Connecting an
external 24 volt power supply to these terminals has no effect because the control card cannot be powered with external voltage.
7.2.2.4 Terminal strip and connection ADP200-...-24-I01 models
8 digital inputs (DI) + 1 Enable input (EN-HW) + 1 motor protection input (MO) + 2 digital outputs (DO) + 3 analog
inputs (AI) + 2 relay outputs (RO) .
EXP-IO-D10A3R2-ADP
T3
T2
T1
Commands
Associated parameter
+ 24V (from PLC)
Fault State (to PLC)
+ 24V (from PLC)
Drive R
eady (to PLC)
Associated parameter
Motor protection input
Motor protection input
Analog input 2X
Analog input 2X
Analog input 1X
Analog input 1X
Analog input 1 (Sensor)
Commands
Associated parameter
Fault R
eset (from PLC)
Start (from PLC)
Enable (from PLC)
RO
2O
RO
2C
RO
1O
RO
1C
DO
2
DO
1
DO
PS PE
MO1
-
MO1
+
AI
2–
AI
2+
AI
1–
AI
1+
AIS
IN+
AIS
24V
AIS
0V PE
DI
8
DI
7
DI
6
DI
5
DI
4
DI
3
DI
2
DI
1
EN
HW
DIO
CM
0V
I/O
24V
I/O
54 55 56 57 26 27 29 99
80 81 40 41 42 43 70 71 72 99
1
2
3
4
5
6
7
8
9 10 11 12
Note!
+24Vdc voltage, which is used to externally supply the regulation card has to be stabilized and with a maximum ±10% tolerance. The maximum absorption
is 1A. It is not suitable to power supply the regulation card only through a unique rectifier and capacitive filter.
If the control is powered with a +24V external, you have to insert a protective diode as described in "Figure 7.3.1.6: External diode on +24V external".
7.2.3 Feedback Connection
This section describes the feedback connections for the standard ADP200-...-RS series.
For optional cards see section A3 of the Appendix.
The names of the terminals and of the relative connection differs for the various card versions.
For more information
see section A3 of the Appendix
.
Caution