Fuji Xerox DocuPrint CM225FW Скачать руководство пользователя страница 273

Страница: 273 / 344

Troubleshooting

273



Clearing Paper Jams From the Center Output Tray

IMPORTANT:

•

To prevent electric shock, always turn off the printer and disconnect the power cord from the grounded outlet before
performing maintenance.

•

To avoid burns, do not clear paper jams immediately after printing. The fusing unit becomes extremely hot during use.

NOTE:

•

To resolve the error displayed on the touch panel, you must clear all print media from the print media path.

Push the rear cover handle and open the rear cover.

Lift up the levers.

Remove any paper jammed from the rear of the printer by carefully pulling it in the direction of the arrow shown
in the following illustration.

Содержание DocuPrint CM225FW
























































































































































































































































































































































Результаты поиска

Содержание DocuPrint CM225FW

Отзывы:

Бренды по названию

Популярные бренды

Fuji Xerox DocuPrint CM225FW, Руководство пользователя

Результаты поиска

Содержание DocuPrint CM225FW

Отзывы:

Бренды по названию

Популярные бренды