Fluke 6270A Скачать руководство пользователя страница 91

Страница: 91 / 144

Pressure

Controller/Calibrator

Module Calibration

c. Read zOffset of slot

•

CAL:PRES(n):ZERO:VAL?

•

Run As Found data for pressures defined in the calibration matrices at the

end of this manual.

•

Run the calibration routine found in the

2-point calibration (zero/span)

menu.
1. Select

SETUP>Module Information>Slot(n)>

Calibrate - where (n) is the

slot number.
a. Enter calibration password – default is

6270

b. Make sure the Product is connected to the pressure source.
c. Touch

Continue

d. Input the pressure prompted on the front panel.
e. Use the touchscreen to select the “reference” field and type the

reference pressure value from the reference.

f. Touch

Enter

– wait approximately 5 seconds and the screen changes

to the second point.

g. Input the pressure prompted on the front panel.
h. Use the touchscreen to select the “reference” field and type the

reference pressure value from the reference.

i. Touch

Enter

– wait approximately 2 seconds and the screen prompts

“Store Coefficients?”.

j. Touch

Continue

•

Run As Left data for pressures defined in calibration matrices. See

Calibration Tables

Calibration of Modules in Calibration Sled

Document the current serial number, calibration date, C0, C1, zOffset with the

remote communication via RS232 (null modem).

Note

The calibration returns units of psi. If you calibrate in kPa, values
need to be converted to kPa.

1. Read Serial number of the module in the calibration sled.

*IDN?

2. Read Calibration date of the module, enter

CAL_DATE?

3. Read C0, enter

OFFSET_SET?

4. Read C1, enter

GAIN_SET?

Содержание 6270A

















































































































































Результаты поиска

Содержание 6270A

Отзывы:

Fluke 6270A, Руководство по обслуживанию, Страница: 91 / 144

Результаты поиска

Содержание 6270A

Отзывы: