Fluke 6270A Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 144

Fluke 6270A Скачать руководство пользователя страница 41

Pressure

Controller/Calibrator

Module Guide Rails

35

PMM Dock Assembly

Use the PMM dock assembly to mount the PM600 and PM200 transducer

modules.



Warning

To prevent possible electrical shock, fire or personal injury,
turn off the Product and disconnect the mains power cord prior
to the removal procedure. Shut off the supply pressure and
vent the system before removing the manifold, valve, or
associated parts.

To remove the PMM dock assembly or associated parts, see Figures 17, 18, and 19:
1.  Make sure the Product is off and disconnect the mains power cord.
2.  Shut off supply pressure and vent the system.
3.  Remove all pressure lines and fittings from the manifold if necessary to move

equipment.

4. Remove the PCM and PMM modules from all slots. See

PMM and PCM

Removal

.

5. Remove the test manifold.
6. Remove top panel, see

Top Panel

.

7. Remove the COMM Tray, see

Communications Tray

.

8. Open the module bay. Pull the latch



to remove the tab of the door frame



that blocks the door open sensor



.

9. Disconnect the power cable



from the PCM solenoid driver PCA J1



.

«
...
39
40
41
42
43
...
»

Содержание 6270A

















































































































































Отзывы:

Нет отзывов