Fluke 6270A Скачать руководство пользователя страница 21

Страница: 21 / 144

Pressure

Controller/Calibrator

Theory of Operation

PCA Overview

Main PCA

- This PCA manages system functions, contains all external

communication ports, all system configuration settings, and is the central PCA for

internal chassis communications. The main PCA is powered by 24 V dc from the

main power supply. There is no calibration data stored on this PCA.
LED indication (located on the main PCA, near the main processor):

•

Application running - pause, blink, blink at 0.6 second intervals

•

Application not Running - full on or full off

•

Operating system/firmware - kernel and main firmware.

Touchscreen PCA

- This PCA works with the touchscreen. The touchscreen

and display are factory aligned.

Solenoid Driver PCA

- This PCA interfaces through the canbus with the main

processor and modules. This PCA manages the solenoid drivers for isolation

valves in the main chassis and is the input point for the module bay open/closed

switch.
LED indication (located on the solenoid driver PCA which is on the PCM dock

manifold):

•

Application running - on/off, blink at 1 second intervals

•

Application running - no communication - on/off, blink at 2 second intervals

•

Downloading or no application loaded - pause, double blink

•

Not functioning - full on or full off

Solenoid Driver PCA – PMM block

- This PCA is an extension from the PCM

solenoid.

PM200 PCA

- Pressure measurement PCA. Calibration data is stored on this

PCA.
LED indication (located on the PM200 module PCA - visible when you service

the PM200 module):

•

Application running - on/off blink at 1 second intervals

•

Application running, no communication - on/off blink at 2 second intervals

•

Downloading or no application loaded - pause, double blink

•

Not functioning - full on or full off

PM600 PCA

- Same PCB as the PM200 but includes a barometric sensor.

Содержание 6270A

















































































































































Результаты поиска

Содержание 6270A

Отзывы:

Fluke 6270A, Руководство по обслуживанию, Страница: 21 / 144

Результаты поиска

Содержание 6270A

Отзывы: