manualshive.com logo in svg

Fluke 6270A, Руководство по обслуживанию, Страница: 121 / 144

Поделиться
Скачать
Fluke 6270A Скачать руководство пользователя страница 121

 Pressure 

Controller/Calibrator 

 

Troubleshooting 

115 

 

Control 

The Control diagnostics menu shows information about the PCM:  

•

 

Port Pressure

 –

 

This menu shows the pressure measurement at the test, 

supply, and exhaust ports.

  

•

 

Control Module 

– This menu shows the PCM model number, serial number, 

and firmware version.

 

•

 

Control Coefficients

 – This menu shows the control coefficients (C0) the 

PCM uses. To change the coefficients, tune the PCM with the autotune 

function located in this menu.  

•

 

Autotune

 

–

 

Autotune is a fully-automated procedure that runs the Product 

through a series of pressures across its ranges. The Product then alters the 

control coefficients to provide the best control performance. Only use 

autotune when the control performance is unacceptable. The system must be 

leak free, have minimal external volume, and the sealing plug on the test port 

must be rated for the maximum pressure of the system. 

1.  Plug the test port and make sure connections are capable of accepting 

pressures of 90 % FS of the highest module installed in chassis. 

2. Select 

SETUP>Tasks>Leak Test

, refer to 

Leak Test

. 

Note 

With the test port plugged and no external volume, System Leak is 
expected to achieve better than 0.04 %FS/Min rate. 

3. Select 

SETUP>Diagnostic>Control>Primary>Autotune

. 

This process should take 20 minutes to 40 minutes. If there are leaks or the 

volume is too large to run autotune, then system will error or timeout. 

Leak Test 

To perform a basic leak test, select the pressure range then select 

SETUP>Tasks>LeakTest

. Complete the following entries: 

a.  Setpoint – Pressure set point at which to perform the leak test 
b.  Stability – After achieving the setpoint, the time in seconds to wait for stability 

before the Duration of the test begins.   

c.  Duration – The time in seconds to collect data for the leak-rate calculation 
d.  Mode – Defaults to external, not selectable 
e.  Run – Starts the test 
f.  Exit – Exits the leak test 

Note 

With the test port plugged and minimal external volume, system leak 
is expected to achieve less than 0.04 % FS/minute change. To 
resolve this performance, stability time must be set to allow thermal 
changes to stabilize. This time is typically greater than 60 seconds 
and up to 240 seconds, depending on testing conditions. 

To assist with evaluation of internal leak and valve performance, use the 

Pneumatic Self-Test function located on the Measure Diagnostic screen. 

Содержание 6270A

















































































































































Отзывы:

Нет отзывов