Fluke 6270A Скачать руководство пользователя страница 15

Страница: 15 / 144

Pressure

Controller/Calibrator

Theory of Operation

Theory of Operation

This section provides a block diagram discussion of the Product pneumatic,

mechanical, electrical, and communication design.

Note

In many of the procedures in this manual, the Product is referred to
as the Unit Under Test (UUT).

Overview

Main Chassis

- includes the main processor with chassis interface, front-panel

processor, GUI interface, module interfaces, solenoid drivers, and distribution of

power, communications, and pneumatic pressure.

PMM

- are available in multiple pressure ranges and performance ratings. All

PMMs use the same pneumatic and electrical connections. Each module carries

and applies full characterization and calibration data to the communicated output

pressure. The test port is protected by a relief valve. The power supply is fully or

partially isolated as required for the sensor type.

PCM

- uses a different mechanical footprint from the PMMs and an identical

electrical connector. PCMs accept pressure supply from the main chassis up to

3300 psi, exhaust pressure to an exhaust port, and regulate pressure on the test

port. The PCM monitors and controls each port for safe operation. The primary

sensor controls feedback to the system-selected PMM.

Accessories

Isolation Valve

- The isolation valve connects pneumatically to the UUT test

port. When activated in the main firmware, the isolation valve treats the UUT as a

module and protects the device during venting and pressure supply release. The

valve allows for internal-only leak testing.

CPS

- Two-stage filter with exhaust and purge valves that capture contamination

from the UUT. Solenoids are driven from the UUT rear-panel solenoid driver

connector when activated in the main firmware.

Test Stand

- Supports extension of the main chassis test port to a convenient

test connection.

Pneumatic and Electrical Configuration

This section provides a discussion of the pneumatic and electrical configuration.

Pneumatics

- The main chassis accepts a maximum of five PMMs with full-scale

up to 20 MPa (3000 psi) and one PCM. The main chassis has independent

pneumatic isolation of both test and reference ports for each of the PMM slots.

For basic operation, a PCM and at least one PMM must be installed. System

configurations depend on the type of PMM modules installed. PMMs vary by

pressure range, absolute or gauge native mode, and if the PMM can be used as

a barometric sensor. Each PMM slot in the main chassis and the test port

handles the full range of available modules (0 psi - 3000 psi). See Figure 1.

Содержание 6270A

















































































































































Результаты поиска

Содержание 6270A

Отзывы:

Fluke 6270A, Руководство по обслуживанию, Страница: 15 / 144

Результаты поиска

Содержание 6270A

Отзывы: