Fluke 6270A Скачать руководство пользователя страница 58

Страница: 58 / 144

6270A

Service Manual

Remove Keypad PCA and Knob from the Front-Panel Assembly

To remove the keypad PCA and knob from the front panel, see Figure 29:
1.  Shut off supply pressure and vent the system.
2.  Remove all pressure lines and fittings from the manifold.
3.  Remove the front-panel assembly as explained in the

Remove Front-Panel

Assembly

section.

4. Use a T10 Torx to remove the six screws that hold the panel shell to the front

panel.

5. As you separate the display panel shell from the front panel, disconnect the

keyboard cable.

6. Remove the encoder assembly cable



from J3 of the keypad PCA.

7. Remove the nine hexalobular keyboard PCA screws



with a Torx T10.

8. Remove the keypad PCA



from the front panel.

9. Remove the number keypad



from the front panel.

10. Remove the power keypad



from the front panel.

11. Remove the encoder knob



from the encoder assembly



12. Use a 13 mm deep socket to remove the jam nut and washer from the

encoder assembly. The jam nut and washer are part of the encoder

assembly.

To install the keypad PCA and encoder knob to the front-panel assembly, do this

procedure in reverse. Complete the procedure detailed in the section to attach

the front panel to chassis.

Содержание 6270A

















































































































































Результаты поиска

Содержание 6270A

Отзывы:

Fluke 6270A, Руководство по обслуживанию, Страница: 58 / 144

Результаты поиска

Содержание 6270A

Отзывы: