Fluke 6270A Скачать руководство пользователя страница 70

Страница: 70 / 144

6270A

Service Manual

Note

Make sure to not interchange the coils or valves between
apply/release valves.

a. Use a 3/4 inch wrench and remove the coil-retaining nut



from the

control valve (apply) coil



or (release) coil



. This should only be hand

tight or very loosely tightened with a 3/4 inch wrench.

b. Remove the coil for the valve to be inspected or replaced.
c. Remove the four screws



with a # 2 Phillips screwdriver and remove

entire valve assembly.

d. Inspect the valve by using a 7/8 inch deep socket or open wrench to

remove the valve stem



from the valve base



To install the valves, reverse these steps.

Inspect the Control Valves

To inspect the control valves, see Figure 37:
1. After the control valve is removed as detailed in the

Removing Control Valves

section, inspect the valve-body surface



and valve-base orifice



to make

sure no damage, particles, or contamination exists. The Product ships with

blue color material on the valve body



2. Make sure the shim



is installed in the valve shaft. If not installed, poor

control and a loud buzzing sound in the control results.

3. Verify the valve assembly order



hxn405.eps

Figure 37. Internal Valve Inspection

Содержание 6270A

















































































































































Результаты поиска

Содержание 6270A

Отзывы:

Fluke 6270A, Руководство по обслуживанию, Страница: 70 / 144

Результаты поиска

Содержание 6270A

Отзывы: