Fluke 6270A Скачать руководство пользователя страница 50

Страница: 50 / 144

6270A

Service Manual

Remove and Inspect the G-Series Valves

To remove the G-series valve, see Figure 24.
1. Use a small flat-head screwdriver to remove the c-clip



2. Remove the coil



and washer



from the valve shaft



. Note the

orientation of the washer, the chamfered side faces the coil bottom (flat side

faces the base).

3. Use a 5.5 mm wrench to remove the valve shaft and valve body



from the

base



4. Inspect the seat on the valve body.
5. Inspect the O-ring



in the valve base.

6. To remove the valve base or the entire valve, use a pin wrench



Install the G-Series Valves

1. Use the pin wrench

to ensure that the base is installed. See Figure 24.

Ensure the O-ring is in the base.

2. Install the valve body into the valve shaft. Ensure the seat of the valve body is

facing up so it makes contact with the orifice on the valve base when re-

installed.

3. Install the valve shaft

and valve body into the base

and tighten using a

5.5 mm wrench.

4. Install the coil washer (chamfer up) onto the valve shaft.
5. Install the coil onto the valve shaft and install the c-clip.

Содержание 6270A

















































































































































Результаты поиска

Содержание 6270A

Отзывы:

Fluke 6270A, Руководство по обслуживанию, Страница: 50 / 144

Результаты поиска

Содержание 6270A

Отзывы: