Fluke 6270A Скачать руководство пользователя страница 46

Страница: 46 / 144

6270A

Service Manual

Table 4. G- and B-Series Valves

PCM DockB3

Valve

J12-SOLR (8 pin)

Pins

J10-SOLT (10 pin)

Pins

Note

1 and 2

N/A

No connection on pins 7
and 8.

3 and 4

N/A

5 and 6

N/A

1 and 2

N/A

3 and 4

N/A

5 and 6

N/A

9 and 10

PMM Dock

Valve

J2-SOLR (8 pin)

Pins

J1-SOLT (10 pin)

Pins

Note

1 and 2

N/A

No connection on pins 7
and 8.

3 and 4

N/A

5 and 6

N/A

1 and 2

No connection on pins
7,8, 9, and 10.

N/A

3 and 4

N/A

5 and 6

Remove and Inspect the B-Series Valves

For this procedure, see Figure 21.

1. Use a 9/16 inch nut driver or wrench to remove the nut



that holds the

B-series valve coil.

2. Remove the coil



and coil washer



from the valve. Note that the

rubber on the washer makes contact with the bottom of the coil when

reassembled.

3. Use a large flat-head screwdriver to remove the valve shaft and valve

body



4. Inspect the seal



for contamination or excessive wear.

5. Inspect the O-ring



, and base orifice



. If any parts are damaged,

remove the base



with a #2 Phillips screwdriver and replace the entire

valve. The entire valve can be ordered from Fluke Calibration.

Содержание 6270A

















































































































































Результаты поиска

Содержание 6270A

Отзывы:

Fluke 6270A, Руководство по обслуживанию, Страница: 46 / 144

Результаты поиска

Содержание 6270A

Отзывы: