Fluke 6270A Скачать руководство пользователя страница 85

Страница: 85 / 144

Pressure

Controller/Calibrator

Calibration and Adjustment Procedures

Item

Minimum Use

Specifications

Equipment Notes

Barometric
Reference

Range: 70 KPa to
110 kPa

Barometric range RPM3
or RPM4

Must interface with Piston
Gauge or COMPASS for
Pressure

Instrument
manuals, work
instructions,
specifications, and
other
documentation for
any associated
equipment.

Software -
Required if you are
not using the on-
board calibration
routine in the
Product menu.

•

COMPASS for

pressure calibration
software

•

COMPASS for

pressure unit of
measure converter

•

(version 5.x.0 or

newer)

•

(version x.0x Build x or

newer).

Standard PC

Windows 7, 8, or 10

Level vial

To estimate verticality to
the acceleration of gravity.

Ruler

To measure head height
differences between the
reference and the UUT.

Pressure tubing
and fittings as
required and
appropriate for the
pressure range
and system.

Calibration procedures described in this section, will need:

•

If a PG7000 Piston Gauge is used:

Calibrated and approved piston gauge (PG) base platform.

Calibrated and approved piston-cylinder for the range to be calibrated.

Calibrated and approved mass set compatible with P-C and PG base

being used and capable of generating the force necessary for the

recommended calibration points.

•

If a FPG8601 is used:

Calibrated and approved FPG.

Test pressure controller.

Dual volume unit (DVU).

Содержание 6270A

















































































































































Результаты поиска

Содержание 6270A

Отзывы:

Fluke 6270A, Руководство по обслуживанию, Страница: 85 / 144

Результаты поиска

Содержание 6270A

Отзывы: