Fluke 6270A Скачать руководство пользователя страница 120

Страница: 120 / 144

6270A

Service Manual

114

System

The system diagnostics menu supplies information on these system components:

•

Door Switch

– This is a mechanical-electrical switch near the front panel that

senses when the panel is open. When open, the system vents and the

module information screen shows. When closed, the system operates

normally. If the status shows “Open” when the door is closed, the switch

could be malfunctioning or need adjustment.

•

Test Port Vent Valve

and

Ref Port Vent Valve

– These are normally-closed

isolation valves installed on the internal pressure manifold. When the system

is in the vent mode, these valves should be open. In other modes, such as

control and measure, the valves should be closed. If the status is different

than that described, the valve may be malfunctioning.

•

Ref Port Vent Valve

– This is a normally-closed isolation valve installed on

the internal pressure manifold. When in gauge measurement mode, the valve

is closed. When in absolute or tare, the valve is open. If the status is different

than described, the valve may be malfunctioning.

Measure

The Measure diagnostics menu shows information on each PMM connected:

•

PMM

– This is the PMM range and name.

•

Pressure

– This is the pressure measured by the sensor in the PMM.

•

Temperature

– This is the ambient temperature inside the PMM. The

temperature inside the PMM can be as much as 5

C higher than room

temperature during normal operation.

•

Test Valve and Ref Valve

– This is a normally-closed isolation valve

installed on the internal pressure manifold in front of each PMM. The test

valve isolates pressure to the PMM and is controlled by the internal software.

When a PMM is selected in the Module Selection menu, the test valve should

be open. For manual testing and troubleshooting, select a single PMM and

test the valve. In other modes such as Fast and Auto, the Product opens and

closes the valves based on a control algorithm. If the status is different than

described, the valve may be malfunctioning.

At the bottom of the menu, there is a pneumatic self-test function that

automatically tests each PMM to verify that the valves are opening and closing

properly. The system controls pressure as necessary and monitors the valve

states. If a valve is not functioning properly, an error is shown that indicates

which valve is malfunctioning.

Содержание 6270A

















































































































































Результаты поиска

Содержание 6270A

Отзывы:

Fluke 6270A, Руководство по обслуживанию, Страница: 120 / 144

Результаты поиска

Содержание 6270A

Отзывы: