Fluke 6270A Скачать руководство пользователя страница 119

Страница: 119 / 144

Pressure

Controller/Calibrator

Troubleshooting

113

Table 48. Troubleshooting (cont.)

Problem Probable

Cause

Action

Pressure Generation or Indication Problems

Product does
not control
down

Blocked exhaust port

Remove shipping plugs or excessive restriction.

Setpoint applied below
atmosphere

Connect vacuum pump.

Slew Rate set to zero

Increase slew rate.

No remote
communications

Communication
settings are not correct

See

Remote Port Menu

Improper command
syntax

Verify cable type (null modem)

Cables are the wrong
type or not properly
connected

Use the correct cables and connections.

Confirm setting in the
Product

Reset Controller Settings

Some of the setup menus have a reset button to reset the settings on the current

menu to their default values. Reset only resets the settings on the screen being

viewed and no others. This is a helpful troubleshooting tool in case an accidental

change was made to the values.
A factory-reset function is available in the Setup menu. Push Reset to reset the

Product to original factory settings.

Diagnostics

The Diagnostics menu provides helpful system information, tools, and functions

to help troubleshoot and keep the system in good operation.

Note

If the Product is configured as a system, the Diagnostics menu
shows all of the controllers connected to it in the Diagnostics menu.

The Diagnostics menu has these sections which are explained in the next

sections:

•

System

•

Measure

•

Control

•

Remote

Interface

Содержание 6270A

















































































































































Результаты поиска

Содержание 6270A

Отзывы:

Fluke 6270A, Руководство по обслуживанию, Страница: 119 / 144

Результаты поиска

Содержание 6270A

Отзывы: